How to make colored smoke bomb
In this video you will learn how to make the most powerful bomb color at all
Materials needed:
Potassium nitrate, sugar, sodium carbonate (baking powder), colored dye
Mix the potassium nitrate with sugar
Amount of 60 Cram potassium with 40 grams sugar
Place the mixture over low heat and stir
Until the sugar is in the form of sticky (Carmela)
Continue stirring until it becomes as follows
Such as peanut butter
Add one teaspoon of sodium carbonate (Bakeng powder)
Which would slow down the combustion process
Add 3 tablespoons of the dye
Orange or blue dye gives the best results
Then stir well
The mixture should look like this
Make a small cup of cardboard and fill it mixture
Enter rarely thick inside the mix
Leave the pen into the mix for an hour to be mold making
Remove the pen
Enter the fireworks fuse
And fill in the blanks of cotton
Wrap duct tape bomb suspicion cylindrical
The bomb was ready!
Do not forget to leave a hole in the top of the bomb
What do you think of this colorful bomb!?
How to moon walk like Michael Jackson
The Moon Walk is one of the most famous dance moves of all time. Done properly the Moon Walk can't fail to impress. Learn how to dance the Michael Jackson way with dance guru Anthony King in this simple three minute tutorial on the moon walk technique.
How To Pick a Lock
Step 1: Get a paperclip
Get a paperclip or safety pin and bend it straight. Now make a slight upwards bend at the very end.
Tip
You can buy a professional lock pick set at a hardware store. There is a basic size intended for American locks.
Step 2: Insert the wrench
Insert your wrench into the lower part of the keyhole—that is, the side opposite the one where the key's teeth would go in.
Step 3: Determine direction
Figure out which way the lock needs to be turned to open by turning the wrench clockwise and then counterclockwise. You'll feel which way has more give.
Step 4: Turn the lock
Turn the lock the correct way with the wrench, putting slight pressure on it. Hold the wrench in place.
Step 5: Insert the paperclip
While keeping pressure on the lock, insert the end of the paperclip into the top part of the keyhole.
Step 6: Feel for pins
Feel around the keyhole with the paperclip until you locate the pins. If you're picking a common door lock, there will most likely be at least five of them in a row.
Tip
Before you start, many experts suggest "raking" the lock. Straighten your second paperclip, put a few bends at the wire's end, and—with no pressure on your wrench—shove it to the back of the lock. Now pull it out quickly, pressing against the top of the lock while gently turning your wrench. You might just set a pin or two that way.
Step 7: Push up
Get a paperclip or safety pin and bend it straight. Now make a slight upwards bend at the very end.
Tip
You can buy a professional lock pick set at a hardware store. There is a basic size intended for American locks.
Step 2: Insert the wrench
Insert your wrench into the lower part of the keyhole—that is, the side opposite the one where the key's teeth would go in.
Step 3: Determine direction
Figure out which way the lock needs to be turned to open by turning the wrench clockwise and then counterclockwise. You'll feel which way has more give.
Step 4: Turn the lock
Turn the lock the correct way with the wrench, putting slight pressure on it. Hold the wrench in place.
Step 5: Insert the paperclip
While keeping pressure on the lock, insert the end of the paperclip into the top part of the keyhole.
Step 6: Feel for pins
Feel around the keyhole with the paperclip until you locate the pins. If you're picking a common door lock, there will most likely be at least five of them in a row.
Tip
Before you start, many experts suggest "raking" the lock. Straighten your second paperclip, put a few bends at the wire's end, and—with no pressure on your wrench—shove it to the back of the lock. Now pull it out quickly, pressing against the top of the lock while gently turning your wrench. You might just set a pin or two that way.
Step 7: Push up
Now for the actual "picking." One at a time, push each pin up with the paperclip. Try to feel for the moment when the pin reaches its "unlocked" position. You should feel a slight give—or even hear a faint click.
Tip
Start with the pin furthest away from you—then move on to the next.
Step 8: Increase the pressure
As you go, apply slightly more pressure with the wrench until you have all the pins lifted up.
Step 9: Turn the wrench
Now turn the wrench fully. Voila! The lock will pop open.
Did You Know?
Wooden locks were used as far back as 4,000 years ago in ancient Egypt.
Start with the pin furthest away from you—then move on to the next.
Step 8: Increase the pressure
As you go, apply slightly more pressure with the wrench until you have all the pins lifted up.
Step 9: Turn the wrench
Now turn the wrench fully. Voila! The lock will pop open.
Did You Know?
Wooden locks were used as far back as 4,000 years ago in ancient Egypt.
الاشتراك في:
الرسائل (Atom)